News

  • How to avoid or reduce weft detachment, weft shrinkage and looping in the weaving process
    Post time: May-26-2023

    Weft winding is to supply the skein or simple yarn from the spinning department to the weaving department, and the weft winding machine rewinds it into fibers suitable for the size of the shuttle and easy to weave. Generally, if cotton mills produce low-grade fabrics, the weft yarns used are supp...Read more »

  • Operation process of cloth inspection defect detection software
    Post time: May-26-2023

    Most of the cloth inspection machines used in the textile industry are equipped with cloth inspection machine companions. The cloth inspecting machine partner can greatly improve the working speed of the cloth inspecting machine. The operation process of the cloth inspection machine partner is as...Read more »

  • Large roll cloth inspection machine for blanket industry
    Post time: May-26-2023

    Raschel blankets are woven through warp and weft knitting, and then cut through the middle to form the prototype of the blanket. At this time, the blank can only be printed after being inspected and rolled. Here we need a large roll cloth inspection machine,   The use skills of the cloth ins...Read more »

  • Working principle and fault diagnosis of automatic packaging machine
    Post time: May-26-2023

    Abstract: The automatic heat shrinkable packaging machine is a highly automated equipment. Labor cost has an important economic significance, and the diagnosis of faults is also very important. “    Automated operations in the packaging industry are changing the way the packaging process wo...Read more »

  • CCD Automatic Vision Alignment Open Width Machine
    Post time: May-26-2023

    Aiming at the low level of automation of domestic open-width machines, a method based on CCD identification and calibration of missing stitches and PID control is proposed.                                                                VS-E Untwisting, Scouring and Squeezing Machine  Automatic vi...Read more »

  • Fabric common defects
    Post time: May-25-2023

    1. Abrasion point of defective cloth surface: The cloth surface is damaged due to friction or abnormal force. 2. Printing on the back: In the printing process, there is often a padding cloth on the back, so that there are traces of printing on the back of the dyed cloth. 3. Rungs: Quality problem...Read more »

  • Fabric Inspection Standard
    Post time: May-25-2023

    Until now, there is no internationally recognized fabric inspection standard, but Western Europe and the United States have their commonly used ten-point evaluation method and four-point evaluation method to control and deal with fabric defects. These two are the most commonly used systems. l) te...Read more »

  • Technical Manual of VS-E Rope Untwisting Open Width Machine
    Post time: May-25-2023

    one. use: VS-E Rope Untwisting and Open Width Machine: It is used for rope (bundle) scouring, bleaching, dehydration after dyeing, (water tying), untwisting, open width (open width water absorption) drying, shaping, etc. for fabrics in the printing and dyeing industry. Indispensable special equip...Read more »

  • ReHow Slitting Machine Principle
    Post time: May-23-2023

    Brief introduction of RH-400 slitting machine: Slitting machine is a kind of mechanical equipment that cuts wide-width fabric or film into multiple narrow-width materials. It is often used in textile and garment industry and printing and packaging industry. In the past, the speed of the magnetic ...Read more »

  • Safety operation rules for loom maintenance, shaft loading and overhaul
    Post time: May-23-2023

    1. As a principle, the operation should be carried out after the main power supply is cut off. If the operation needs to be carried out while the main power supply is on, the stop button should be locked; for electrical maintenance and repair operations, qualified electrical security workers shou...Read more »

  • Ribbon machine safety operating procedures
    Post time: May-23-2023

    Ribbon machine safety operating procedures 1. Place the loom in a well-ventilated place with no flammable materials around, clean ground, no dust, and a relatively dry place. 2. It is strictly forbidden to expose the loom to rain, snow and water vapor. 3. The distance between the loom and the ope...Read more »

  • Types of looms|ReHow
    Post time: May-23-2023

    The ribbon loom is made of various yarns as raw materials into ribbon or tubular weave object equipment. There are many types of yarns used in ribbons, including plain weave, Twill, satin, joint weave, double layer, multi-layer tubular and jacquard wait. There are generally three production metho...Read more »